When your heat pump quits, you need heat pump repair Milwaukie OR homeowners actually recommend. We service every major brand, from Carrier and Trane to Mitsubishi Electric and Daikin, and we carry the parts to fix most failures on the first visit. Whether it's a frozen coil in January or a capacitor that died in July, we get your system running again fast. Call (855) 947-9500 for same-day heat pump service Milwaukie.
Heat pump repair Milwaukie OR is the diagnostic and mechanical work that restores a failing heat pump to full heating and cooling capacity. It starts with a full electrical and refrigerant check: manifold gauges on the service ports, a clamp meter on the compressor windings, and a multimeter across the capacitor and contactor. From there we isolate the actual failure, whether that's a refrigerant leak in the copper tubing, a clogged PVC condensate line, or a blower motor that's drawing too many amps.
Most Milwaukie homes run a heat pump year-round, so a failure hits hard. In Clackamas County, we see two peak seasons: the first cold snap in November, and the July heat that pushes a tired compressor past its limit. If you're searching for heat pump repair near me Milwaukie OR on a Sunday night, that's usually a capacitor or a thermostat that lost its programming. We answer those calls 24/7 and stock the common parts on every truck.
Every heat pump repair Milwaukie OR visit covers a full diagnostic and the repair itself. Here's what's included in a standard call, and what we quote separately if your system needs it.
We test the thermostat, control board, capacitor, contactor, blower motor, and compressor windings with a multimeter and clamp meter. Refrigerant pressures get checked with manifold gauges. This is included in every repair visit.
If pressures are low, we use an electronic leak detector and pressure test to find the leak in the copper tubing or Schrader ports. Repairing the leak and recharging with R-410A is quoted based on the location and size of the leak.
Failed capacitors, contactors, thermostats, and blower motors are replaced with OEM-grade parts. We stock the common failures on the truck, so most replacements happen on the first visit without a return trip.
A clogged PVC condensate line is one of the most common reasons a heat pump shuts down in cooling mode. We clear the line, flush the trap, and check the drain pan for standing water before we leave.
We check the air filter, inspect the evaporator coil for frost or dirt, and measure static pressure in the ductwork. Restricted airflow makes a heat pump work harder and shortens compressor life.
After the repair, we run a complete heating and cooling cycle and verify the temperature split at the return and supply. We check amp draw against the nameplate and confirm the system holds under load.
We ask what the system is doing: no heat, no cool, short cycling, or a breaker that trips. That five-minute call tells us which parts to load and whether this is a same-day repair or an after-hours emergency. You get a two-hour arrival window, not a vague all-day promise.
The technician tests the thermostat, control board, capacitor, contactor, and blower motor with a multimeter and clamp meter. We check refrigerant pressures with manifold gauges and inspect the copper tubing and PVC condensate line for leaks or clogs. This takes 30 to 45 minutes and pinpoints the failure.
Before any work starts, you get the diagnosis in plain language and a flat price for the fix. If the repair is straightforward, like a capacitor or a clogged drain, we quote it on the spot. If it's a refrigerant leak, we explain the leak detection and recharge cost separately.
We pull a vacuum with the vacuum pump before adding R-410A, recover old refrigerant with the recovery machine, and replace failed components with OEM-grade parts. Most repairs take one to three hours. We protect your floors, and we clean up every bit of old parts and packaging.
We run a full heating and cooling cycle, verify the temperature split at the return and supply, and check amp draw against the nameplate rating. Then we walk you through what failed, what we replaced, and how to keep it from happening again. You get photos of the failed part if you want them.
We ask what the system is doing: no heat, no cool, short cycling, or a breaker that trips. That five-minute call tells us which parts to load and whether this is a same-day repair or an after-hours emergency. You get a two-hour arrival window, not a vague all-day promise.
Used to read high-side and low-side refrigerant pressures and diagnose charge issues, restrictions, or a failing compressor.
Pulls a deep vacuum on the refrigerant circuit after a leak repair, removing moisture and air before we recharge with R-410A.
Recovers refrigerant safely before we open the system, keeping us compliant with EPA Section 608 rules and keeping refrigerant out of the atmosphere.
Measures amp draw on the compressor and blower motor and tests capacitors, contactors, and control board voltage.
Finds refrigerant leaks in copper tubing, brazed joints, and Schrader ports that a pressure test alone can miss.
Straightens bent condenser fins so airflow across the coil stays unrestricted and the system runs at rated capacity.
A homeowner in Oak Grove called in January with a heat pump that was iced over and blowing cold air. The system had been running constantly for two days. The outdoor coil was blocked with ice, and pressures showed a low refrigerant charge from a slow leak at a brazed joint.
After: We recovered the remaining refrigerant, repaired the leaking joint, pulled a vacuum, and weighed in a fresh R-410A charge. The defrost cycle now completes in under four minutes, and the system holds 70 degrees in the house on a 28-degree night.
Book this service →
A family in Ardenwald had a heat pump that cycled on and off every four minutes. Their power bill had climbed 30 percent over two months. The air filter was clean, but static pressure measured well above ACCA spec because of an undersized return duct.
After: We corrected the return airflow, replaced a worn blower motor that had been running hot, and verified the temperature split. The system now runs 12 to 15 minute cycles and holds the setpoint. Their next bill dropped back to normal.
Book this service →
A homeowner near Lake Road called during a 97-degree afternoon with a heat pump blowing warm air in cooling mode. The compressor was running but not cooling. Amp draw was low, and suction pressure was below normal, pointing to a refrigerant issue rather than an electrical fault.
After: We found a leaking Schrader port, replaced the valve core, pulled a vacuum, and recharged the system. Cooling was restored within three hours of the call, and the house dropped from 84 to 72 degrees by evening.
Book this service →Most heat pump failures fall into a handful of categories. Here are the ones we see most often in Milwaukie and how we handle them.
Ask a pro →We test the reversing valve, defrost board, and auxiliary heat circuit. Most no-heat calls trace back to a failed capacitor, a stuck reversing valve, or a defrost cycle that's not completing. We repair the specific failure and verify heating operation before we leave.
We check the defrost control, outdoor fan motor, and refrigerant charge. A low charge is a common cause of icing, so we leak-test the copper tubing and recharge with R-410A if needed. We also clear the drain path so meltwater doesn't refreeze.
Short cycling usually means a dirty air filter, an oversized system, or a refrigerant charge issue. We check airflow first, then pressures, then the control board. Fixing the root cause stops the cycling and extends compressor life.
This often points to a reversing valve stuck in heating mode, a bad thermostat, or a compressor issue. We diagnose the control circuit and the valve, then repair or replace the failed component. Most of these fixes are done the same day.
Most heat pump repairs in Milwaukie run $180 to $850 in 2026, depending on the failed part and whether refrigerant is involved. A capacitor or contactor replacement sits at the low end. A refrigerant leak repair with recharge, or a blower motor replacement, lands at the high end. We give you the exact price before we start work.
ThermexaPro repairs heat pumps across Milwaukie and Clackamas County, including Oak Grove, Gladstone, and Oregon City. We service Carrier, Trane, Lennox, Goodman, Rheem, York, Mitsubishi Electric, and Daikin systems. Call (855) 947-9500 and we'll book a same-day or next-day visit, whichever fits your schedule.
Yes. We run 24/7 emergency dispatch for no-heat and no-cool calls in the Milwaukie area. If your heat pump dies on a weekend or holiday, call (855) 947-9500 and we'll send the nearest available technician. Most emergency calls in the 97222 ZIP code get a response within a few hours.
The most common causes we find are a failed capacitor, a tripped breaker, a clogged condensate drain, or a dirty air filter that's choked the blower. Less often it's a refrigerant leak or a bad thermostat. A quick diagnostic tells us which one it is, and most of these fixes take under two hours.
Licensed, insured, and stocked with the parts your system needs. Call (855) 947-9500 and we'll book a same-day heat pump repair Milwaukie OR visit or dispatch emergency help after hours. One call, one technician, one fixed heat pump.
Call (855) 947-9500 →Call (855) 947-9500 any time, day or night, and a live dispatcher will get a tech headed your way. Regular office hours run 8 a.m. to 6 p.m. Monday through Friday, with 24/7 emergency coverage for no-heat and no-cool calls. You can also email [email protected] and we will reply the same business day.