Full system diagnostic
We test the refrigerant circuit with manifold gauges, the control board with a multimeter, and the blower motor with a clamp meter. That takes 30 to 45 minutes and tells us exactly what failed before we quote a single part.
Same-day service, 24/7 emergency response across Clackamas County
Heating and cooling repair near me Milwaukie OR
When you search for heating and cooling repair near me Milwaukie OR, you want a tech who shows up today, not next week. ThermexaPro serves homeowners and businesses across Milwaukie, Oregon and Clackamas County with same-day diagnostics, honest pricing, and repairs done right the first time. Whether your furnace quit at 2 a.m. or your AC is blowing warm air in July, we carry the parts and tools to fix it on the spot.
Careful work. Honest options.
About this service
What heating and cooling repair near me Milwaukie OR really means
heating and cooling repair near me Milwaukie OR is a licensed diagnostic and repair service that restores furnaces, air conditioners, heat pumps, and ducted systems when they stop heating, stop cooling, or start costing you money. It is needed whenever your system short-cycles, blows lukewarm air, leaks refrigerant, or trips the breaker. A proper visit includes a full electrical and refrigerant check, not just a filter swap. We test capacitors, contactors, blower motors, and thermostat wiring with a multimeter and clamp meter before we quote a single part.
Milwaukie homes take a beating from wet winters and dry, smoky summers. Furnaces that sat idle from April to October often fail on the first cold snap, and AC units that ran fine last August can freeze up when the first 90-degree day hits. If you need Milwaukie OR heating and cooling repair, we stock R-410A refrigerant, universal capacitors, and common blower motors on every truck. That means most repairs finish in one visit, not two. We also handle 24/7 heating and cooling repair in Milwaukie when a no-heat call can't wait until morning.
- ✓ Same-day repair slots
- ✓ Upfront flat-rate pricing
- ✓ Parts stocked on every truck
- ✓ 24/7 emergency response
What's included
What our heating and cooling repair near me Milwaukie OR includes
Every repair visit covers a full diagnostic, the repair itself, and a post-repair test. Here is what is standard on the call versus what we quote separately, so there are no surprises when the invoice arrives.
Flat-rate written quote
You see the price on paper before work starts. It lists the failed component, the labor, and the warranty. No hourly meter, no surprise line items, no pressure to replace a system that only needs a repair.
Repair with stocked parts
Our trucks carry R-410A refrigerant, capacitors, contactors, igniters, and common blower motors for Carrier, Trane, Lennox, Goodman, Rheem, and York equipment. That inventory is why most repairs finish in one visit.
Post-repair performance test
After the fix, we run a full heating or cooling cycle and measure the temperature split at the register. If the system is not hitting the right numbers, we keep working until it does. You see the results before we pack up.
Written parts and labor warranty
Every repair carries a written warranty on both the part and our labor. If the same component fails inside the warranty window, we come back and fix it at no charge. That is a real commitment, not a marketing line.
Maintenance recommendation
We tell you what to watch for and when to schedule the next tune-up. A pre-summer AC tune-up or winter furnace tune-up catches small problems before they turn into emergency calls on the coldest or hottest day of the year.
How it works
How our repair process works
You call (855) 947-9500 and talk to a real dispatcher, not a call center. We ask what your system is doing, how old it is, and whether you have heat or cooling at all. That five-minute conversation lets us load the right parts before the truck rolls.
Your tech arrives in a marked van, pulls on shoe covers, and runs a full diagnostic: manifold gauges on the refrigerant circuit, a multimeter on the control board, and a clamp meter on the blower motor. Expect 30 to 45 minutes. You get the findings in plain English, not jargon.
Before any repair starts, you see a flat-rate price on paper. It lists the failed part, the labor, and the warranty. If the fix is not worth it on a 20-year-old unit, we tell you that too and quote a replacement instead. No pressure either way.
Once you approve, we make the repair. Capacitor swaps take 20 minutes; blower motor replacements run 90 minutes to two hours. After the fix, we run the system through a full heating or cooling cycle and verify the temperature split at the register before we pack up.
We show you what failed, what we replaced, and how to keep it running. You get a written warranty on parts and labor, plus a reminder for your next tune-up. If anything we touched fails inside the warranty window, you call us and we come back at no charge.
STEP 01Phone triage
You call (855) 947-9500 and talk to a real dispatcher, not a call center. We ask what your system is doing, how old it is, and whether you have heat or cooling at all. That five-minute conversation lets us load the right parts before the truck rolls.
Tools & methods
Tools and methods we use on every repair
Manifold gauges
Used to read high-side and low-side refrigerant pressures on AC and heat pump systems. The pressure readings tell us whether the charge is low, high, or right where it should be.
Vacuum pump and recovery machine
When a repair requires opening the refrigerant circuit, we recover the existing charge with a recovery machine, then pull a deep vacuum with the vacuum pump before recharging. This is EPA Section 608 required practice.
Multimeter and clamp meter
The multimeter tests control boards, thermostats, and wiring. The clamp meter reads amp draw on the blower motor and compressor, which tells us whether a component is failing or just working harder than it should.
Leak detector
Electronic leak detectors find refrigerant leaks at Schrader valves, flare fittings, and coil joints. Finding the leak is the only way to fix it properly instead of just topping off the charge.
Fin comb and duct cleaning vacuum
The fin comb straightens bent condenser fins to restore airflow. The duct cleaning vacuum removes debris from ductwork and returns. Both are standard on our maintenance and repair visits.
Tube bender and thermostat screwdriver set
The tube bender shapes copper tubing during line-set repairs without kinking it. The thermostat screwdriver set lets us open and service Nest, Ecobee, and standard thermostat housings without stripping screws.
Real results
Before and after.
heating and cooling repair near me
No-heat furnace restored in one night
A homeowner in Ardenwald called at 11 p.m. in January with a furnace blowing cold air. The house had dropped to 54 degrees. The furnace was a 12-year-old Goodman with a failed igniter and a dirty flame sensor.
After: Our tech arrived at 1 a.m., replaced the igniter, cleaned the flame sensor, and verified the ignition sequence. Heat was back on within 40 minutes. The temperature split at the register read 42 degrees, right in spec.
Book this service →
heating and cooling repair near me
Warm-air AC fixed without replacement
A homeowner in Oak Grove was told by another company that their 9-year-old Trane AC needed full replacement. The system was blowing warm air and the compressor was short-cycling. The quoted replacement was over $6,000.
After: We tested the capacitor and found it reading 40 percent below rated microfarads. We replaced the capacitor, found and repaired a Schrader valve leak, and recharged the system with R-410A. Total cost was under $500, and the AC cooled the house to 72 degrees that afternoon.
Book this service →
heating and cooling repair near me
Heat pump defrost failure resolved
A heat pump in Linwood was icing over every few hours in January, forcing the auxiliary heat strips to run constantly. The power bill had jumped by $180 in one month, and the house still felt cold.
After: We diagnosed a failed defrost control board on the Mitsubishi Electric unit. After replacing the board, the heat pump returned to normal defrost cycles and carried the heating load again. The auxiliary strips stopped running, and the next power bill dropped back to normal.
Book this service → Problems we solve
Common heating and cooling problems we fix in Milwaukie
Most no-heat and no-cool calls trace back to a handful of failures. Here are the ones we see most often in Milwaukie homes, what happens if you ignore them, and how we fix them.
Ask a pro →Furnace will not ignite on a cold night
We test the igniter, flame sensor, and gas pressure, then replace the failed component. Most ignition repairs finish in under an hour, and we check the heat exchanger for cracks while we are in there.
AC blows warm air in July
We check the capacitor and contactor first, then test the refrigerant charge with manifold gauges. If there is a leak, we locate it with a leak detector, repair it, and recharge with R-410A.
System short-cycles every few minutes
We check airflow first, then test the thermostat and control board. A dirty air filter or clogged condensate drain is a quick fix. If the thermostat is malfunctioning, we can install a Nest or Ecobee while we are there.
Frozen evaporator coil blocks cooling
We thaw the coil, clear the clogged condensate drain and PVC line, then find the root cause. Usually it is a dirty filter or low charge. We verify the fix with a temperature split test before we leave.
Proof you can check
Licensed, certified, and reviewed
- NATE Certification · North American Technician Excellence
- EPA Section 608 Universal · U.S. Environmental Protection Agency
- Oregon CCB Licensed Contractor · Oregon Construction Contractors Board
- ACCA Standards Compliance · Air Conditioning Contractors of America
- OSHA Safety Compliance · Occupational Safety and Health Administration
Most repairs in Milwaukie run $180 to $650 in 2026, including the diagnostic. A capacitor or igniter swap sits at the low end; a blower motor or refrigerant leak repair lands higher. Emergency calls inside Milwaukie city limits carry no after-hours premium. You get a flat-rate written price before we start, so the number you hear on the phone is the number you pay.
ThermexaPro does, and we have since 2023. Our NATE-certified techs cover Milwaukie, Oak Grove, Gladstone, Oregon City, West Linn, and the rest of Clackamas County. Call (855) 947-9500 and a live dispatcher schedules you, usually same-day. We stock R-410A, capacitors, contactors, and common blower motors on every truck, so most repairs finish in one visit.
Yes. We run 24/7 heating and cooling repair in Milwaukie, including nights, weekends, and holidays. No-heat calls in January and no-cool calls in August get priority dispatch. A tech is typically on-site within two to four hours for addresses in the 97222 and 97269 ZIP codes. Call (855) 947-9500 and we will give you a real ETA, not a window.
Look for three things: a live phone number, NATE or EPA Section 608 credentials, and a written flat-rate quote before work begins. ThermexaPro meets all three. We are Oregon CCB licensed, insured, and based right here in Milwaukie. Call (855) 947-9500, describe the symptom, and we will tell you whether it is a same-day fix or something that can wait.
Ready when you are
Get heating and cooling repair near me Milwaukie OR today
No heat, no cool, or a system that is short-cycling? Call (855) 947-9500 and a live dispatcher will schedule you, usually same-day. NATE-certified techs, stocked trucks, flat-rate pricing, and a written warranty on every repair.
Book Same-Day Service (855) 947-9500 →
Request an appointment
Contact ThermexaPro in Milwaukie
Call (855) 947-9500 any time, day or night, and a live dispatcher will get a tech headed your way. Regular office hours run 8 a.m. to 6 p.m. Monday through Friday, with 24/7 emergency coverage for no-heat and no-cool calls. You can also email [email protected] and we will reply the same business day.
Call anytime(855) 947-9500Email the office[email protected]
Office hoursOpen 24 hours · 7 days a week